| Operating System |
| Crestron 3-Series; real-time, preemptive, multi-threaded/multitasking kernel; Transaction-Safe Extended FAT file system; supports up to 10 simultaneously running programs; preloaded DMPS3 .AV Framework Base Program |
| Memory |
| SDRAM |
512 MB |
| Flash |
4 GB |
| Communications |
| Ethernet |
10/100/1000 Mbps, auto-switching, auto-negotiating, auto-discovery, full/half duplex, industry-standard TCP/IP stack, UDP/IP, CIP, DHCP, SSL, TLS, SSH, SFTP (SSH File Transfer Protocol), FIPS 140-2 compliant encryption, IEEE 802.1X, SNMP, BACnet™/IP [8], IPv4 or IPv6, Active Directory authentication, IIS v.6.0 Web Server, SMTP e-mail client, RSTP, Private Network Mode |
| Control Subnet |
10/100/1000 Mbps Ethernet, auto-switching, auto-negotiating, auto-discovery, full/half duplex, DHCP server, DNS Server, port forwarding, Isolation Mode, IEEE 802.3at Type 1 compliant PoE PSE |
| Cresnet |
Cresnet master mode |
| USB |
USB signal routing via select DM transmitters and receivers, or via USB-EXT-DM extenders [7]; USB device port for computer console (setup) |
| RS-232 |
2-way device control and monitoring up to 115.2k baud with hardware and software handshaking |
| IR/Serial |
1-way device control via infrared up to 1.2 MHz or serial TTL/RS-232 (0-5 Volts) up to 115.2k baud; supports CNXRMIRD IR Receiver [4] |
| DigitalMedia |
DM 8G+, HDCP 2.2, EDID, CEC, PoDM+ [6], Ethernet |
| HDBaseT |
HDCP 2.2, EDID, CEC, RS-232, PoE+ [6], Ethernet |
| HDMI |
HDCP 2.2, EDID, CEC |
| NOTE: Supports management of HDCP and EDID; supports management of CEC between the connected HDMI and HDBaseT devices and the control system |
| Video |
| Switcher |
7×2 matrix, Crestron QuickSwitch HD technology |
| Scalers (HDMI output) |
(1) 4K video scaler with motion-adaptive deinterlacing, intelligent frame rate conversion, Deep Color support, 3D to 2D conversion [3], content-adaptive noise reduction, and widescreen format selection (zoom, stretch, maintain aspect-ratio, or 1:1) |
| Input Signal Types |
HDMI w/Deep Color, 3D [3], & 4K (DVI & Dual-Mode DisplayPort compatible [2]); DM 8G+ & HDBaseT w/Deep Color, 3D [3], & 4K |
| Output Signal Types |
HDMI w/Deep Color & 4K (DVI compatible [2]); DM 8G+ & HDBaseT w/Deep Color, 3D, & 4K |
| Maximum Resolutions |
Scan
Type |
Resolution |
Frame
Rate |
Color
Sampling |
Color
Depth |
| Progressive |
4096×2160 DCI 4K
&
3840×2160 4K UHD |
24 Hz |
4:4:4 |
30 bit |
| 30 Hz |
4:4:4 |
24 bit |
| 30 Hz |
4:2:2 |
36 bit |
| 60 Hz |
4:2:0 |
24 bit |
| 2560×1600 WQXGA |
60 Hz |
4:4:4 |
36 bit |
| 1920×1080 HD 1080p |
60 Hz |
4:4:4 |
36 bit |
Interlaced
(excluded on
HDMI output) |
1920×1080 HD 1080i |
30 Hz |
4:4:4 |
36 bit |
|
| NOTE: Common resolutions are shown; other custom resolutions are supported at pixel clock rates up to 300 MHz. Interlaced video is not supported on the HDMI outputs. |
| Audio – General |
| Switcher/Mixer |
12×5 stereo source matrix switcher, digital & analog source inputs, 6-channel gated mic mixer w/DSP, independent mixer per analog output (6-ch mic + 1 stereo source), independent stereo DSP per analog output, integrated power amplifier, two independent digital output mixers (6-ch mic + 1 stereo source), 2×1 digital output mix selector per digital output |
| Analog-To-Digital Conversion |
24-bit 48 kHz |
| Digital-To-Analog Conversion |
24-bit 48 kHz |
| Frequency Response, Digital & Analog Line Outputs |
20 Hz to 20 kHz ±0.5 dB (digital source);
20 Hz to 20 kHz ±0.5 dB (analog line source);
20 Hz to 20 kHz ±0.7 dB (microphone source) |
| Frequency Response, Speaker Output |
20 Hz to 20 kHz ±1 dB @ 20 Watts into 8 Ohms;
100 Hz to 20 kHz ±2.5 dB @ 70 or 100 Volts |
| S/N Ratio, Digital & Analog Line Outputs |
>108 dB, 1 kHz, A-weighted (digital source);
>103 dB, 1 kHz, A-weighted (analog line source) |
| S/N Ratio, Speaker Output |
98 dB @ 20 Watts into 8 Ohms, 1 kHz, A-weighted;
96 dB @ 20 Watts into 4 Ohms, 1 kHz, A-weighted |
| THD+N, Digital & Analog Line Outputs |
<0.002%, 20 Hz to 20 kHz (digital source);
<0.005%, 20 Hz to 20 kHz (analog line source);
<0.05%, 20 Hz to 20 kHz (microphone source) |
| THD+N, Speaker Output |
<0.1%, 1 kHz @ 20 Watts into 4 or 8 Ohms;
<0.7%, 20 Hz to 20 kHz @ 20 Watts into 4 or 8 Ohms |
| Stereo Separation, Digital & Analog Line Outputs |
>108 dB (digital source);
>103 dB (analog source) |
| Stereo Separation, Speaker Output |
>65 dB @ 20 Watts, 1 kHz |
| Channel Separation, Digital Outputs |
>108 dB (digital source);
>103 dB (analog source) |
| Channel Separation, Analog Line Outputs |
>103 dB |
| Speaker Output Modes |
4Ω/8Ω stereo, 70V mono, or 100V mono |
| Speaker Amplifier Output Power |
20 Watts RMS per channel @ 8 Ohms, 4 Ohms tolerant;
40 Watts RMS @ 70 or 100 Volts |
| Audio – Microphone Inputs |
| Typical of 6 microphone input channels (Mic/Line 1 – 6) |
| Input Signal Types |
Mono analog mic or line level |
| Phantom Power |
Enable/Disable per channel |
| Gain |
0 to +60 dB Gain adjustment, plus Mute |
| Delay |
0.0 to 85.0 ms |
| EQ Center Frequencies |
50 to 200 Hz (Band 1), 200 to 800 Hz (Band 2), 800 to 3.2k Hz (Band 3), 3.2k to 12.8k Hz (Band 4) |
| EQ Gain |
±12.0 dB per band |
| High-Pass Filter |
On or Off |
| Gating Threshold |
-80 to 0 dB |
| Gating Depth (Attenuation) |
-80 to 0 dB |
| Gating Attack |
1 to 250 ms |
| Gating Release |
1 to 1000 ms |
| Compression Threshold |
-80 to 0 dB |
| Compression Ratio |
1:1 to 10:1 |
| Compression Attack |
1 to 250 ms |
| Compression Release |
1 to 1000 ms |
| Compression Curve |
Hard or soft knee |
| Audio – Source Inputs |
| Input Signal Types |
HDMI (Dual-Mode DisplayPort compatible [2]) on Inputs 1-6, DM 8G+ & HDBaseT on Input 7, analog 2-channel on Aud In 1-5 |
| Analog Formats |
Stereo 2-channel |
| Digital Formats |
2-channel LPCM |
| Input Compensation |
±10.0 dB, adjustable per input |
| Audio – Analog Line & Speaker Outputs |
| Typical of 1 analog line/speaker output (Program Out & Speaker Outputs) and 2 analog line outputs (Aux Out 1 – 2) |
| Output Signal Type/Format |
Stereo 2-channel |
| Mic 1 – 6 |
-80 to +10 dB Level adjustment range, plus Mute and Pan |
| Mics Master |
-80 to +10 dB Level adjustment range, plus Mute |
| Source |
-80 to +10 dB Level adjustment range, plus Mute and Balance |
| Master Volume |
-80 to +10 dB Level adjustment range, plus Mute and Mono |
| Mixer Presets |
1 through 5 |
| Bass |
±12.0 dB |
| Treble |
±12.0 dB |
| Equalization |
10-band graphic + 4-band parametric |
| GEQ Center Frequencies |
31.5, 63, 125, 250, 500, 1k, 2k, 4k, 8k, 16k Hz |
| GEQ Gain |
±12.0 dB per band |
| PEQ Center Frequencies |
10 to 22000 Hz per band |
| PEQ Gain |
-36.0 to +24.0 dB per band |
| PEQ Bandwidth |
0.02 to 3.50 octaves per band |
| PEQ Types |
Peaking EQ, High Pass, Low Pass, High Shelf, Low Shelf, Notch |
| Delay |
0.0 to 85.0 ms |
| Limiter Threshold |
-80 to 0 dB |
| Limiter Ratio |
1:1 to 10:1 |
| Limiter Attack |
1 to 250 ms |
| Limiter Hold |
1 to 200 ms |
| Limiter Release |
1 to 1000 ms |
| Limiter Curve |
Hard or soft knee |
| EQ Presets |
1 through 10 (includes Delay and Limiter settings) |
| Audio – Digital Outputs |
| Typical of 2 digital outputs (HDMI Output 1 & DM Output 2) |
| Output Signal Types |
HDMI (DVI compatible [2]) on Output 1, DM 8G+ & HDBaseT on Output 2 |
| Formats |
2-channel LPCM |
| Digital Output Mix Select 1 – 2 |
Selects which mix is routed to the corresponding output |
| Typical of 2 digital output mixers: |
| Mic 1 – 6 |
-80 to +10 dB Level adjustment range, plus Mute and Pan |
| Mics Master |
-80 to +10 dB Level adjustment range, plus Mute |
| Source |
-80 to +10 dB Level adjustment range, plus Mute and Balance |
| Master Volume |
-80 to +10 dB Level adjustment range, plus Mute |
| Mixer Presets |
1 through 5 |
| Connectors – Audio/Video Inputs |
| AUD IN 1 – 5 |
(5) 5-pin 3.5 mm detachable terminal blocks;
Balanced/unbalanced stereo line-level analog audio inputs;
Input Impedance: 24k Ohms balanced/unbalanced;
Maximum Input Level: 4 Vrms balanced, 2 Vrms unbalanced |
| MC1/LN1 – MC6/LN6 |
(6) 5-pin 3.5 mm detachable terminal blocks;
Comprises (6) balanced microphone/line audio inputs;
Balanced Mic Input Level: -60 to 0 dBV, 1 Vrms maximum;
Balanced Line Input Level: -31 to +11 dBV, 3.7 Vrms maximum;
Unbalanced Line Input Level: -37 to +5 dBV, 1.85 Vrms maximum;
Mic Input Impedance: 3.9k Ohms balanced;
Line Input Impedance: 19k Ohms balanced, 9.5k Ohms unbalanced;
Phantom Power: 48 Volts DC, software enabled/disabled per channel |
| HDMI 1 – 6 INPUTS |
(6) 19-pin Type A HDMI female;
Digital video/audio inputs;
(DVI and Dual-Mode DisplayPort compatible [2]) |
| DM INPUT 7 |
(1) 8-pin RJ45 female, shielded;
DM 8G+ input, HDBaseT compliant;
PoDM+ PSE port (HDBaseT PoE+ compatible) [6];
Connects to the DM 8G+ output of a DM transmitter or other DM device, or to an HDBaseT device, via CAT5e, Crestron DM-CBL-8G, or Crestron DM-CBL-ULTRA cable [5] |
| Connectors – Audio/Video Outputs |
SPEAKER OUTPUT
4Ω/8Ω L – R |
(2) 2-pin 7.62 mm 15A detachable terminal blocks;
4-8 Ohm stereo speaker-level audio output;
Wire Size: Terminals accept up to 14 AWG (2.5 mm²);
Output Power: 20W RMS per channel stereo at 8 Ohms, 4 Ohms tolerant |
SPEAKER OUTPUT
70/100V |
(1) 2-pin 7.62 mm 15A detachable terminal block;
Transformer-isolated 70 or 100 Volt mono speaker-level audio output;
Wire Size: Terminals accept up to 14 AWG (2.5 mm²);
Output Power: 40W RMS mono at 70 or 100 Volts;
Note: 4Ω/8Ω and 70/100V outputs are mutually exclusive |
| PROG OUT |
(1) 5-pin 3.5 mm detachable terminal block;
Balanced/unbalanced stereo line-level audio output;
Output Impedance: 200 Ohms balanced, 100 Ohms unbalanced;
Maximum Output Level: 4 Vrms balanced, 2 Vrms unbalanced |
| AUX OUT 1 – 2 |
(2) 5-pin 3.5 mm detachable terminal blocks;
Balanced/unbalanced stereo line-level audio outputs;
Output Impedance: 200 Ohms balanced, 100 Ohms unbalanced;
Maximum Output Level: 4 Vrms balanced, 2 Vrms unbalanced |
| HDMI 1 OUTPUT |
(2) 19-pin Type A HDMI female;
Digital video/audio outputs;
(DVI compatible [2]) |
| DM OUTPUT 2 |
(1) 8-pin RJ45 female, shielded;
DM 8G+ output, HDBaseT compliant;
PoDM+ PSE port (HDBaseT PoE+ compatible) [6];
Connects to the DM 8G+ input of a DM receiver or other DM device, or to an HDBaseT device, via CAT5e, Crestron DM-CBL-8G, or Crestron DM-CBL-ULTRA cable [5] |
| Connectors – Control & Power |
| IR/SERIAL OUT 1 – 4 |
(4) 2-pin 3.5 mm detachable terminal blocks;
IR/Serial output ports;
IR output up to 1.2 MHz;
1-way serial TTL/RS-232 (0-5 Volts) up to 115.2k baud |
| IR IN |
(1) 3-pin 3.5 mm detachable terminal block;
For connection of the CNXRMIRD IR Receiver [4];
Allows control from IR wireless remotes using RC-5 command set |
| INPUT 1 – 4 |
(1) 5-pin 3.5 mm detachable terminal block;
Comprises (4) programmable digital inputs;
Input Voltage Range: 0 to 24 Volts DC, referenced to GND;
Logic Threshold: 2.5 Volts DC nominal with 1 Volt hysteresis band;
Input Impedance: 10k Ohms at >5 Volts, 1M Ohms at <5 Volts;
Pull-up Resistor: 2.2k Ohms per input |
| RELAY 1 – 4 |
(1) 8-pin 3.5 mm detachable terminal block;
Comprises (4) normally open, isolated relays;
Rated 1 Amp, 30 Volts AC/DC;
MOV arc suppression across contacts |
| COM A – B |
(2) DB9 male;
Bidirectional RS-232 ports;
Up to 115.2k baud, hardware and software handshaking support |
| NET |
(4) 4-pin 3.5 mm detachable terminal blocks;
Cresnet Master ports, paralleled;
Available Cresnet Power: 30 Watts |
| PoDM+ INPUT PWR |
(1) Combo D-Sub 7w2, male;
48 Volt DC power input for PoDM power supply [6];
Enables PoDM+ power sourcing on each DM INPUT/OUTPUT port;
Enables PoE power sourcing on the CONTROL SUBNET port |
| SERVICE |
(1) USB Type B female;
For factory use only |
| 100-240V~4.0A 50/60Hz |
(1) IEC 60320 C14 main power inlet;
Mates with removable power cord, included |
| G |
(1) 6-32 screw;
Chassis ground lug |
| CONTROL SUBNET |
(1) 8-pin RJ45, female;
10Base-T/100Base-TX/1000Base-T Ethernet port;
PoE PSE (Power Sourcing Equipment) port [6];
Provides a dedicated local network for Crestron devices |
| LAN |
(1) 8-pin RJ45 female;
10Base-T/100Base-TX/1000Base-T Ethernet port |
| COMPUTER (front) |
(1) USB Type B female;
USB computer console port (for setup only) |
| Controls & Indicators |
| PWR |
(1) Green LED, indicates operating power supplied from AC power line |
| NET |
(1) Yellow LED, indicates Cresnet bus activity |
| LAN |
(1) Yellow LED, indicates Ethernet activity |
| HW-R |
(1) Recessed pushbutton for hardware reset, reboots the control system |
| SW-R |
(1) Recessed pushbutton for software reset, restarts the software program |
| LCD Display |
(1) Green LCD alphanumeric; adjustable backlight; 2 lines x 20 characters per line; displays input/outputs by name, volume levels, setup menus, signal routing, device info, and other system information |
| SOFTKEYS |
(4) Pushbuttons for activation of LCD driven functions and passcode entry |
| MENU |
(1) Pushbutton, steps menu back one level |
| Λ, V |
(2) Pushbuttons, for scrolling up or down through the menu and adjusting menu parameters |
| ENTER |
(1) Pushbutton, executes the highlighted menu or value |
| VOLUME |
(1) Continuous turn rotary encoder, adjusts menu parameters, defaults to Program audio volume |
| MUTE |
(1) Pushbutton and red LED, mutes the Program audio output |
| INFO |
(1) Pushbutton and red LED, selects INFO mode to view AV and device info |
| ROUTE |
(1) Pushbutton and red LED, selects ROUTE mode to allow routing changes |
| VIEW |
(1) Pushbutton and red LED, selects VIEW mode to view current routing |
| INPUT 1 – 7 |
(7) Pushbuttons and red LEDs, each selects the corresponding video input for routing |
| OUTPUT 1 – 2, PROG, AUX 1 – 2 |
(5) Pushbuttons and red LEDs, each selects the corresponding video or audio output for routing |
| SPEAKER OUTPUT (rear) |
(1) 3-position slide switch, selects the amplifier output configuration |
| DM INPUT 7 (rear) |
(2) LEDs, green LED indicates DM link status, amber LED indicates video and HDCP signal presence |
| DM OUTPUT 2 (rear) |
(2) LEDs, green LED indicated DM link status, amber LED indicates video and HDCP signal presence |
| CONTROL SUBNET (rear) |
(2) LEDs, (1) green and (1) amber, for indication of Ethernet speed, activity, and link status |
| LAN (rear) |
(2) LEDs, (1) green and (1) amber, for indication of Ethernet speed, activity, and link status |
| Power |
| Main Power |
4 Amps @ 100-240 Volts AC, 50/60 Hz |
| Power Consumption |
65 Watts typical;
49 Watts idle |
| Available Cresnet Power |
30 Watts |
| Power over DM (PoDM) |
IEEE 802.3at compliant PoDM+ PSE (Power Sourcing Equipment), each DM INPUT/OUTPUT port supplies up to 30 Watts to power one PoDM (Class 0-3) or PoDM+ (Class 4) PD (Powered Device) [6] |
| Power over HDBaseT |
IEEE 802.3at PoE+ compliant PSE (Power Sourcing Equipment), each DM INPUT/OUTPUT port supplies up to 30 Watts to power one HDBaseT PoE or PoE+ PD (Powered Device) [6] |
| Power over Ethernet (PoE) |
IEEE 802.3at compliant PoE PSE (Power Sourcing Equipment), the CONTROL SUBNET port supplies up to 15.4 Watts to power one PoE (Class 0-3) PD (Powered Device) [6] |
| PoDM Power Supply |
Compatible with model PW-4830DUS or DM-PSU-3X8-RPS [4] |
| Environmental |
| Temperature |
41° to 104° F (5° to 40° C) |
| Humidity |
10% to 90% RH (non-condensing) |
| Heat Dissipation |
222 BTU/hr typical;
167 BTU/hr idle |
| Ambient Noise |
28.4 dBA typical/idle;
47 dBA maximum |
| Enclosure |
| Chassis |
Metal, black finish, fan-cooled, vented sides |
| Front Panel |
Metal, black finish with polycarbonate label overlay |
| Mounting |
Freestanding or 3 RU 19-inch rack-mountable (adhesive feet and rack ears included) |
| Dimensions |
| Height |
5.20 in (133 mm) without feet |
| Width |
17.28 in (439 mm);
19.00 in (483 mm) with rack ears |
| Depth |
15.75 in (400 mm) |
| Weight |
| 15.5 lb (7.1 kg) |
| Maximum DM 8G+ Cable Lengths |
|
Resolution |
Cable Type |
DM-CBL-ULTRA
DigitalMedia Ultra Cable |
DM-CBL-8G
DigitalMedia 8G™ Cable |
CAT5e
(or better) [5] |
| 1080p60 Full HD |
330 ft (100 m) |
330 ft (100 m) |
330 ft (100 m) |
| 1920×1200 WUXGA |
| 1600×1200 UXGA |
| 2048×1080 DCI 2K |
| 2560×1440 WQHD |
230 ft (70 m) |
165 ft (50 m) |
| 2560×1600 WQXGA |
| 3840×2160 4K UHD |
| 4096×2160 DCI 4K |
|
Reviews
There are no reviews yet.