MXA710 Linear Array Microphone
0- Category:SHURE
Specifications
All specifications measured from narrow lobe width. Values for all widths are within ± 3 dB of these specifications unless otherwise noted.
General
Lobe Width
| Adjustable | Narrow | 30 degrees |
| Medium | 40 degrees | |
| Wide | 70 degrees |
Connector Type
RJ45
Power Requirements
Power over Ethernet (PoE), Class 0
Power Consumption
10 W maximum
Weight
| MXA710-2FT | 2 lbs (0.91 kg) |
| MXA710-4FT | 3.7 lbs (1.67 kg) |
Product Dimensions
| MXA710-2FT | 0.87 x 2.36 x 25.04 in. (22.09 x 60 x 636 mm) H x W x L |
| MXA710-4FT | 0.87 x 2.36 x 49.12 in. (22.09 x 60 x 1247.76 mm) H x W x L |
Control Software
Shure Designer
Plenum Rating
UL2043 (Suitable for Air Handling Spaces)
Dust Protection
IEC 60529 IP5X Dust Protected
Operating Temperature Range
−6.7°C (20°F) to 40°C (104°F)
Storage Temperature Range
−29°C (-20°F) to 74°C (165°F)
Audio
Frequency Response
100 Hz to 20 kHz
AES67 or Dante Digital Output
| Channel Count | MXA710-2FT | 6 total channels (4 independent transmit channels, 1 Automix output, 1 AEC reference in channel) |
| MXA710-4FT | 10 total channels (8 independent transmit channels, 1 Automix output, 1 AEC reference in channel) | |
| Sampling Rate | 48 kHz | |
| Bit Depth | 24 | |
Sensitivity
at 1 kHz
| MXA710-2FT | -7.4 dBFS/Pa |
| MXA710-4FT | -7.9 dBFS/Pa |
Maximum SPL
Relative to 0 dBFS overload
| MXA710-2FT | 101.4 dB SPL |
| MXA710-4FT | 101.9 dB SPL |
Signal-To-Noise Ratio
Ref. 94 dB SPL at 1 kHz
71.2 dB A-weighted
Latency
Does not include Dante latency
| Direct Outputs | 8.7 ms |
| Automix output (Includes IntelliMix processing) | 19.3 ms |
Self Noise
| MXA710-2FT | 22.9 dB SPL-A |
| MXA710-4FT | 22.8 dB SPL-A |
Dynamic Range
| MXA710-2FT | 78.5 dB |
| MXA710-4FT | 79.1 dB |
Built-in Digital Signal Processing
Automatic mixing, Acoustic Echo Cancellation (AEC), Noise Reduction, Automatic Gain Control, Compressor, Delay, Equalizer (4-band Parametric) , Mute, Gain ( 140 dB range)
Acoustic Echo Cancellation Tail Length
Up to 250 ms
Networking
Cable Requirements
Cat 5e or higher (shielded cable recommended)
MXA710 Frequency Response
Frequency response measured directly on-axis from a distance of 6 feet (1.83 m).
Lobe Sensitivity
The edge of the blue coverage area for each channel represents where the sensitivity reaches -6 dB. Understanding how lobe sensitivity is displayed helps to:
- Provide complete coverage in a space, either by adding lobes or changing the lobe width. This ensures the sensitivity is within 6 dB in all areas. It is acceptable for lobes to slightly overlap.
- Ensure that spacing and isolation are adequate to reduce noise and maximize automatic mixing performance.
Measured at 1 kHz, on-axis
Reviews
There are no reviews yet.